1 |
In an INTEL 8085 microprocessor the
ADDRESS-DATA bus and the DATA bus are |
Options |
A) Non multiplexed |
B) Multiplexed |
C) Duplicated |
D) Same as CONTROL bus |
|
|
|
Correct Answer |
B |
|
2 |
A 3 ½ digit nultimeter has an accuracy specification of (± 0.5%
of reading ± 5 counts). If the meter reads 2.00 mA on a full scale
of 20mA, the worst-case error in the reading is
|
Options |
A) 0.5% |
B) 2.5%
|
C) 3.0% |
D) 5.5%
|
|
|
|
Correct Answer |
C |
|
3 |
The measurements of a source voltage are 5.9V,
5.7V and 6.1V. The sample standard deviation of the readings is |
Options |
A) 0.013 |
B) 0.04 |
C) 0.115 |
D) 0.2 |
|
|
|
Correct Answer |
D |
|
4 |
Consider the following systems:
System 2: G(s) =
System 1: G(s) =
The true statement regarding the system is |
Options |
A) Bandwidth of system 1 is greater than the
bandwidth of system 2
|
B) Bandwidth of system 1 is lower than the
bandwidth of system 2
|
C) Bandwidth of both the systems are the same
|
D) Bandwidth of both the systems are infinite
|
|
|
|
Correct Answer |
A |
|
5 |
The transfer function of a system is
The steady-state gain of the system to a unit-step input is |
Options |
A)
|
B) 0 |
C) ¥ |
D) not possible to be determined |
|
|
|
Correct Answer |
C |
|
6 |
In 8085 microprocessor, CY flag may be set by
the instruction |
Options |
A) SUB |
B) INX |
C) CMA |
D) ANA |
|
|
|
Correct Answer |
A |
|
7 |
V1 and V2 are the input
voltages of an instrumentation amplifier. The output of the
instrumentation amplifier is found to be 100(V1 – V2)
+ 10-4 (V1 + V2). The gain and the
common mode rejection ratio (CMRR) of the instrumentation amplifier
respectively are |
Options |
A) (50, 60 dB)
|
B) (50, 120 dB)
|
C) (100, 60dB)
|
D) (100, 120 dB)
|
|
|
|
Correct Answer |
C |
|
8 |
The sequence x[n] whose z-transform is X[z] = e(1/Z) is
|
Options |
A)
u[n] |
B)
u[-n] |
C) (-1)n
u[n] |
D)
u[-n-1] |
|
|
|
|
9 |
The time taken by an ionized atom, of mass m kg
and charge e Coulombs, pulsed into a field-free region with V volts,
to reach a detector L meters away is |
Options |
|
|
|
Correct Answer |
B |
|
10 |
The clock frequency of a timer-counter is
10MHz. The timer-counter is used in the period mode and the
input to the timer-counter is a square wave of frequency 2 kHz. The
display of the timer-counter will show a value |
Options |
A) 200 |
B) 2000 |
C) 5000 |
D) 50000 |
|
|
|
Correct Answer |
C |